Available 4 files for D-Link DI-106M
Select Files
Company
D-Link
Categories
Networks Cards
Model
D-Link DI-106M
Description
Firmware
Operating System
Firmware
Version
150
Size Driver
382KB
File Name
106m150.zip
Observations
Upload New Firmware file via XMODEM:
1. Enter Main Menu through RS-232 port of DI-106(M) using Terminal
Emulator (such as Hyper Terminal of MS-WIN95, PROCOMM Plus,
Vterm ... ).
2. Enter "24. System Maintenance" then "7. Software Update"
and the following message will be displayed.
To update software, system needs to be rebooted.
After system is rebooted, 'Enter Debug Mode' will be displayed.
Please enter 'atur' to upload RAS and ISDN code.
Do you want to continue (y/n):
Please press the "y" key to continue and execut "atur" command
after "Enter Debug Mode".
3. After "atur" executed, the message "Now erase flash ROM for
uploading ..." will showing.
When message "Starting XMODEM upload......." was appeared,
start to upload the right binary file via XMODEM.
4. When the message "Programming successful...OK" appeared, type
"atgo" to reboot.
Company
D-Link
Categories
Networks Cards
Model
D-Link DI-106M
Description
Internet Access Configuration Guide
Information
Manual
Operating System
Manual
Size Driver
104KB
File Name
di_106-300_for_internet_access.pdf
Observations
Setting up DI-106/300 for internet access w/ ISP using dynamic single IP address
Setting up the workstation.
Tcp/ip configuration.
Make sure that you have got the TCP/IP protocol installed. This can be done in control panel, networks.
Screen below shows a PC with TCP/IP protocol loaded.
If it is loaded then look at the properties by selecting the protocol then click on properties.
Select specify an IP address and Subnet mask (IP address should be a valid IP address for your network and the Subnet
mask should also be the right one for the IP address).
Specify the default gateway under the gateway tab.
The gateway will be the IP address of the router. So make a note of the gateway that you enter as you will need it later on.
Specify the DNS settings under the DNS Configuration.
First enable DNS, enter host name, this can be anything you like. In the DNS server search order enter the DNS IP address
provided by your ISP.
That completes the workstation setup.
Router setup
Connect the router’s RS232 port to your PC’s com port (make note of the com port number). Go to
Start, programs, accessories, Hyper terminal. Double click on hyperterm.exe and you will be prompted
for a name
Enter anything you like (router). Then click ok. You will be asked for phone number.
Set connect using to direct to the com port that you are using. (I have got the router connected to com
port 2) then do OK.
It will prompt for com port properties.
The setting should be the same as shown above. If not change the settings so that they are the same.
Then do ok.
You will be prompted with a blank screen with a flashing cursor on the top left hand corner. Press enter
and you will be prompted with the following screen.
The default password is 1234.
Then you will be displayed with the following main menu. To select an option press the number to go
back a menu press escape this will not save the settings. To save the settings go to the bottom of the
screen and confirm the settings.
Company
D-Link
Categories
Networks Cards
Model
D-Link DI-106M
Description
Users Guide
Information
Manual
Operating System
Manual
Size Driver
1.8MB
File Name
di-106_manual.pdf
Observations
INTRODUCTION ....................................................................... 1
Features .................................................................................................... 2
Ease of Installation.............................................................................................. 2
Built-in Hub ....................................................................................................... 2
ISDN Basic Rate Interface (BRI)......................................................................... 3
ISDN Leased Line............................................................................................... 3
Multiple Networking Protocol Support ................................................................ 4
Standard Phone Jacks.......................................................................................... 4
Dial On Demand................................................................................................. 4
Bandwidth On Demand....................................................................................... 4
Full Network Management.................................................................................. 5
RADIUS (Remote Authentication Dial In User Service) ...................................... 5
PPP Security....................................................................................................... 5
MS (Microsoft) CHAP........................................................................................ 5
RIP-1/RIP-2 ........................................................................................................ 6
DHCP Support (Dynamic Host Configuration Protocol)....................................... 6
Call Control ........................................................................................................ 6
Data Compression............................................................................................... 7
Networking Compatibility................................................................................... 7
Applications For Your DI-106 or DI-106M................................................ 7
Internet Access.................................................................................................... 7
Internet Single User Account (SUA).................................................................... 7
Multiprotocol LAN-to-LAN Connection .............................................................. 8
Telecommuting Server ........................................................................................ 8
What This Manual Covers.......................................................................... 8
What This Manual Doesn’t Cover .............................................................. 9
Other Resources ........................................................................................ 9
Packing List............................................................................................... 9
Additional Installation Requirements....................................................... 10
BEFORE YOU BEGIN ............................................................. 11
Company
D-Link
Categories
Networks Cards
Model
D-Link DI-106M
Description
Factory Default Configuration File
Operating System
Software
Size Driver
8KB
File Name
default.cfg
Access to Official Website D-Link
Welcome to the HelpDrivers, driver for printers.
Original files: In HelpDrivers, all drivers, manuals, BIOS, etc. are those originally provided by the official manufacturers. Click here to learn more
You can download by either clicking the 'Download' button. From the File Download window, verify that "Save" is selected and click OK.
Do not rename the file you're downloading, it may cause installation problems.